Power Amplifier - 5C-CA-CS-4000
- Brand: 5CORE Electronics
- Product Code: Power Amplifier - CS 4000
Description
5C-CA-CS-4000 Power Amplifier
·
The inputs
are actively balanced and the overload point is high enough to accept the
maximum output level of virtually any signal source.
· 5C-CA-CS-4000 has two output (speaker) connections per channel.
· Modes of operation:
Ø
Stereo Operation
For stereo (dual channel) operation, turn the amplifier OFF and set the mode select switches on the back panel to the out (extended) position. In this mode, both channels operate independently of each other, with their input attenuators controlling their respective levels. Thus, a signal at channel A's input produces an amplified signal at channel A's output, while a signal at channel B's input produces an amplified signal at channel B's output.
Ø
Bridged Mono
Operation
Both amplifier channels can be bridged together to make a very powerful single-channel monaural amplifier. Use extreme caution when operating in the bridged mode; potentially lethal voltage may be present at the output terminals. To bridge the amplifier, depress the rear panel Bridge switch to the IN position. Direct the signal to channel A's input and connect the speakers across the hot outputs (the "+" binding posts) of channels A and B. Only channel A's input attenuator is active while in Bridge Mono mode.
·
AC Power Switch/Circuit
Breaker for automatic monitoring of the working condition of the amplifiers
·
The input
attenuator controls (one for channel A, one for channel B) located on the front
panel attenuate signal level (decrease gain) for the respective amplifier channels
in all modes.
·
The rear
panel Bridge Select switch determines if the amplifier is in stereo (two
channels) or in Bridged Mono mode.
·
DDT Defeat
Switch in the extended position will prevent excessive distortion and potential
speaker damage.
Technical Specifications:
Rated Power 4 ohms bridged | 2,450 watts @ 1 kHz <0.1% THD |
Rated Power 2 x 2 ohms |
1,375 watts per channel @ 1 kHz <0.1 % THD both channels driven |
Rated Power 2 x 4 ohms |
925 watts per channel @ 1 kHz <0.1% THD both channels driven |
Rated Power 2 x 8 ohms |
625 watts per channel @ 1 kHz <0.1% THD both channels driven |
Minimum Load Impedance |
2 ohms |
Maximum RMS Voltage Swing |
78 volts |
Frequency Response |
10 Hz - 25 kHz; +0, -1 dB at 1 watt |
Power Bandwidth |
10 Hz - 35 kHz; +0, -3 dB at rated 2 ohm power |
T.H.D. 2 x 2 ohms |
78 volts |
Frequency Response |
10 Hz - 25 kHz; +0, -1 dB at 1 watt |
Power Bandwidth |
10 Hz - 35 kHz; +0, -3 dB at rated 2 ohm power |
T.H.D. 2 x 2 ohms |
<0.2% @ 800 W per channel from 20 Hz to 20 kHz |
T.H.D. 2 x 4 ohms |
<0.2% @ 675 W per channel from 20 Hz to 20 kHz |
T.H.D. 2 x 8 ohms |
<0.15% @ 440 W per channel from 20 Hz to 20 kHi |
SMPTE IMD |
<0.1% 60 Hz and 7 kHz, 250 W @ 4 ohms |
Slew Rate |
17 V/uS |
Damping Factor (8 ohms) |
> 400:1 @ 20 Hz - 400 Hz |
Input CMRR |
> -101 dB @ 1 kHz |
Voltage Gain |
x 40 (32 dB) |
Input Sensitivity |
1.32V @ 2 ohms, 1.55 V @ 4 ohms, 1.74 V @ 8 ohms |
Input Impedance |
20k ohms, balanced |
Hum and Noise |
> -114 dB, "A" weighted referenced to rated 4 ohm power |
USP:
·
High
performance
·
Two modes of
operation for ease of installation according to the need of event.
·
Best
suitable for live stage/DJ/studio/auditorium/worship.
·
DDT Defeat
Switch in the extended position will prevent excessive distortion and potential
speaker damage.
·
The rear panel
Bridge Select switch determines if the amplifier is in stereo (two channels) or
in Bridged Mono mode.
Operation Manual